Home > ROUTE FAQs & Tips

ROUTE FAQs & Tips

August 1st, 2015 in ROUTE 300-101 Go to comments

In this article, I will try to summarize all the Frequently Asked Questions in the ROUTE 300-101 Exam. Hope it will save you some time searching through the Internet and asking your friends & teachers.

1. Please tell me how many questions in the real ROUTE exam, and how much time to answer them?

There are 50 questions, including 4 lab-sims. You have 120 minutes to answer them but if your native language is not English, Cisco allows you a 30-minute exam time extension (150 minutes in total).

2. How much does the ROUTE 300-101 cost? And how many points I need to pass the exam?

This exam costs $300. You need at least 790/1000 points to pass this exam.

3. I passed the ROUTE exam, will I get a certificate for it?

No, Cisco does not ship ROUTE Exam certificate, it only ships you a certificate after completing the full CCNP track of 3 exams (ROUTE, SWITCH & TSHOOT) within three years. Once again we have to notice that you need to finish these three exams within three years (not nine years). Many candidates misunderstand this and think they have nine years to complete three exams.

4. Which sims will I see in the ROUTE exam?

The popular sims now are Policy Based routing sim, EIGRP OSPF Redistribution sim, OSPF Evaluation Sim and EIGRP Evaluation Sim and please notice that the IP addresses, router names may be different (it is also true for Drag and Drop questions)

5. How many points will I get for one sim?

Maybe you will get about 80 to 100 points for each sim, just like the CCNA exam.

6. In the real exam, I clicked “Next” after choosing the answer, can I go back for reviewing?

No, you can’t go back so you can’t re-check your answers after clicking the “Next” button.

7. What is the difference between the old BSCI & the new ROUTE exam?

In the new ROUTE exam, there are no IS-IS, DHCP, Multicast questions so you can ignore them if you are reading old BSCI books. In fact, DHCP & Multicast are good topics and maybe you will have a chance to learn about them in other Cisco exams.

8. Can I use short commands, for example “conf t” instead of “configure terminal”? Will I get full mark for short commands?

From the comments on this site, maybe you will get full mark for short commands. But sometimes short commands don’t work so please be careful with them. We highly recommend you should learn the full commands.

9. What are your recommended materials for ROUTE?

There are many materials for learning ROUTE but below are popular materials that many candidates recommend.

Books

CCNP ROUTE Official Certification Guide

ROUTE Student Guide

CCNP ROUTE Portable Command Guide

CCNP Route Quick Reference Sheet

Video training

CBT Nuggets

Simulator (all are free)

 

GNS3 – the best simulator for learning ROUTE

Packet Tracer

10. How much time should I spend on each sim?

You should not spend more than 15 minutes for each sim. Recall that you only have 90 minutes so if you spend 15 minutes for each sim x 4 sims = 60 minutes. The 30 minutes left is for solving 46 multiple choice & drag-and-drop questions. If you are not a native English speaker and have 30-minute expansion (ask the mentor to confirm) than you can spend 20 minutes for each sim.

11. Can I pass without doing sims?

As mentioned above, each sim will cost you from 80 to 100 points. In the real exam you will have to solve 4 sims that give from 320 to 400 points. Suppose you answer all other questions perfectly then you will get 600 to 680 points but the passing score is 790. It means that you surely fail if ignore them.

From the calculation above, if you miss only one sim the chance to pass is average but if you miss two, the chance to pass is very, very low.

12. Are the exam questions the same in all the geographical locations?

Yes, the exam questions are the same in all geographical locations. But notice that Cisco has a pool of questions and each time you take the exam, a number of random questions will show up so you will not see all the same questions as the previous exam.

13. I don’t want to lose points so should I use the “copy running-config startup-config” after finishing each lab-sim?

In the ROUTE exam, we can’t use that command so surely you will not lose any points if not using that command.

14. I passed the ROUTE exam. Do you have any site similar for CCNP exams?
We have certprepare.com for SWITCH, networktut.com for TSHOOT, voicetut.com for CCNA Voice, securitytut.com for CCNA Security, rstut.com for CCIE Written & Lab, dstut.com for CCDA. Hope you enjoy these sites too!

15. Why don’t I see any questions and answers on digitaltut.com? I only see the explanation…

Because of copyrighted issues, we had to remove all the questions and answers. You can download a PDF file to see the questions at this link: http://thongtinthoidai.net/?page=route-questions-and-answers

Is there anything you want to ask, just ask! All of us will help you.

Comments
Comment pages
1 2 3 4 7 205
  1. Anonymous
    October 4th, 2016

    send me plz the valid dump or the new questions to {email not allowed}
    Thanks A lot!

  2. Anonymous
    October 4th, 2016

    send me plz the valid dump or the new questions to ameera.talaat @ gmail.com

  3. Anonymous
    October 4th, 2016

    send me plz the valid dump or the new questions to ameera.talaat5 @ gmail.com

  4. Anonymous
    October 4th, 2016

    send me plz the valid dump or the new questions to rayjameshuntley @ gmail.com

  5. Jerome
    October 5th, 2016

    Can some please send me that latest Dump for 300-101 route at Jeromesinovich”at”gmail.com

  6. A1
    October 5th, 2016

    @doomed, so we can’t use the 149q, Does anyone has updated questions for 300-101?

  7. M
    October 6th, 2016

    Just wrote and i can confirm that 149q is not valid.
    is there any place we can get the new dumps?

  8. soldier
    October 7th, 2016

    send me plz the valid dump or the new questions

    okangulder @ hotmail . com

  9. Anasttom
    October 7th, 2016

    How long does it takes to the new dump release usually?

  10. ahmed
    October 7th, 2016

    kindly i wont the new dump that update in October .. email: {email not allowed}

  11. ahmed
    October 7th, 2016

    kindly i wont the new dump that update in October .. ahmedfarah1042013 @ gmail .com

  12. Digital
    October 9th, 2016

    Anyone have the latest dump ?

  13. tagwa ali
    October 10th, 2016

    for new dump 183q
    send to me in

    tagwatagelsir88 @ gmail . com
    i have it

  14. A1
    October 10th, 2016

    @tagwa ali- Is it confirm that 183q valid?

  15. tagwa ali
    October 10th, 2016

    i dont know
    but this dump in
    passleader & examcollection & vceplus

    i bought it from them

  16. Anonymous
    October 12th, 2016

    @A1 please can you send me a new dump at
    marcoderiggi @ gmail . com

  17. Route_to_go
    October 12th, 2016

    Can anybody send me new dump of 183Q? Plz need help.
    my email whoami1970 at live dot com.

  18. Marcus8888
    October 12th, 2016

    can you post a link for dump of 183Q…. Please need

  19. John Doe
    October 13th, 2016

    Guys are dumps in passleader & examcollection & vceplus still valid ?

    Did anyone studying these dumps did not pass ?

  20. procyber
    October 13th, 2016

    can anybody send me 183q dump from passleader to procyber777 @ gmail . com
    Please!!!

  21. John Doe
    October 13th, 2016

    OK WHO PASSED 300-101 THIS WEEK ?

  22. Anonymous
    October 14th, 2016

    I failed today with 149q

  23. Anonymous
    October 15th, 2016

    Do you all think we should do Switch or Tshoot before those two get updated?

  24. Kyaw Kyaw
    October 15th, 2016

    Hi All,

    Could you please kindly confirm the following CCNP 300-101 new Dump_183 from PassLeader that is updated Dump or not which had fresh 31 Questions totally as per below.
    Somebody can remember it who touched with new dump on this October at the Exam Center. Please share your experience and suguest for it.

    8 new Drag & Drop Question:
    Page 62 Question 85 to Page 67 Question 92

    23 new Multiple-Chose Question:
    Page 67 Question 93 to Page 75 Question 115

    https://drive.google.com/drive/folders/0B8Ss8bHxYejnQzJqMkp2RUVubm8

  25. Anonymous
    October 15th, 2016

    Hi Kyaw,

    I have reviewed the questions and for what i can remember, it does not contain new questions..
    Also there is a new drag & drop question regarding CHAP but I haven’t seen it in this dump.

  26. Kyaw Kyaw
    October 15th, 2016

    @tagwa ali

    are you check my posted dump_183 that is same or not as you bought from passleader?

  27. Anonymous
    October 15th, 2016

    This contains new questions but none of these came out on my exam.
    New questions are about BGP, GRE Tunnel, Frame Relay and new drag and drop.

  28. Anonymous
    October 16th, 2016

    Hi guys i hope you all ok, may anyone please send me the new dumps, i am going to take the exam
    nextweek… my email is {email not allowed}

  29. Anonymous
    October 16th, 2016

    can anybody send me 183q dump from passleader or pass4sure to willy leroy 280 at gmail .com
    Please!

  30. Yaseen
    October 16th, 2016

    Hello All,

    Please email me the dumps for CCNP Routing to Yaseensid12@ gmail . com

    Please

    Thanks

  31. Anonymous
    October 16th, 2016

    good morning all,
    May anybody send me 183q dump from passleader or pass4sure for ccnp routing to willy leroy 280 at gmail .com
    Please!

  32. sofi
    October 16th, 2016

    Guys…anyone cleared ccnp route exam after Oct 1st 2016

  33. routemaster
    October 16th, 2016

    So, is the 183q from passleade valid or not now that the test has been updated?

  34. Peter
    October 17th, 2016

    Dear friends.
    Please send me latest dump ccnp routing.
    Very,very thans.
    {email not allowed}

  35. Peter
    October 17th, 2016

    Dear friends.
    Please send me latest dump ccnp routing.
    Very,very thans.
    kokosik@ mail.t-com. sk

  36. Lisa Chang
    October 17th, 2016

    Hey, Can someone send me the valid dumps please. Cant really afford to failed. Link 999 111 @ yahoo . com. Thank ya so much

  37. rava
    October 18th, 2016

    hi plz can someone send me the valid dumps :( i can also convert it in pdf for free email to

    gaelgsy at gmail dot com

  38. james
    October 18th, 2016

    Hi all,

    Is 183q the valid dump now? I need to know asap please!!

  39. ashraf4y
    October 19th, 2016

    Dear friends.
    Please send me latest dump ccnp routing.Please Please

    ashraf4y @ hotmail

  40. Anonymous
    October 19th, 2016

    Request a help please.

    Who can send me the current dump in October 2016.
    dowdp31 @ hotmail

    A hug !

    thank you

  41. Anonymous
    October 19th, 2016

    Dear brothers and sisters
    please send me the current update dump for the october…i was failed on october 7 i bought 3 books from 3 diff vendors like exam4sure, pass it4sure and dumps4download us…all of them come with the same Q&A yes the simulators are ok.. but no questions from them i did not see those questions and the drag and drop from anywhere, that is why i failed, i am looking for help now to go back…if anyone passed the exam can help me and tell what vendor that has the new update…. or can send me the new questions on my email….(willyleroy 280 @ gmail .com) i would appreciat it thank you…..

  42. Create own dump
    October 19th, 2016

    Hello Everyone

    Rather than asking for the Dumps why don’t we create our own people are previously failed in the exam if they can share with us whatever they remember then we good to go. Lots of people are requesting new dumps but they don’t reliase that there will be no new dumps becuase cisco will not let it happen so please share the question and we will collect the all the question within a week

  43. PI
    October 19th, 2016

    @ Create own dump

    Good idea, I have been planning to do that , can anyone confirm that the labs have remained the same?

  44. yo
    October 19th, 2016

    Good idea but is the 183q still valid?

  45. Create own dump
    October 19th, 2016

    @yo

    Yes, it is still valid you can book the test ???

  46. Create own dump
    October 19th, 2016

    @PI

    labs still the same

  47. HANI
    October 19th, 2016

    @ Create own dump
    are you sure that the 183q dump is valid
    I want to book for the exam this week

  48. Create own dump
    October 19th, 2016

    If the 183q would have been balid you will not see any comment here as I mention earlier we need to create our own dump and people are still asking if any dumps are valid I don’t have any answer to that

  49. HANI
    October 19th, 2016

    @ Create own dump
    SO WHY YOU TOLD @yo THAT THE 183Q IS VALID AND TOLD HIM TO BOOK THE TEST.

  50. Anonymous
    October 19th, 2016

    149 incomplete. Tests earlier this week. All bad.

  51. Ben
    October 19th, 2016

    149 incomplete. Tested earlier this week. Failed.

  52. Create own dump
    October 20th, 2016

    @hani

    Because he is lazy

  53. Ben
    October 20th, 2016

    I just went thru the 183q list.
    As of Monday 10/17, the 183q is incomplete. New subset of questions are in the rotation on top of the 183.

  54. Peter
    October 20th, 2016

    Dear friends.
    Please send me latest dump ccnp routing.
    Very,very thans.
    kokosik@ mail.t-com. sk

    Please,please,please

  55. Test taker
    October 21st, 2016

    I took a test 4 days ago. I didn’t do well.
    there was one question mention about what is the BGP administrative distance?
    like:

    90
    20
    200
    110
    Something like that but i can’t find in 183q

  56. Ben
    October 21st, 2016

    @Test Taker. There were at least 15 questions that I didn’t recognize as well. Including a new BGP based drag and drop.

    I did get the bgp admin distance question you listed as well.

  57. Patricj
    October 21st, 2016

    @Ben

    Can you please share with us any new question that you remember even one question will help us to pass so please share with us

  58. Dump seeker
    October 22nd, 2016

    @ Ben Can you please post here your experience, the question which you find new in your exam.
    It would be helpful for us.

  59. spiderlan03
    October 23rd, 2016

    i will get the exam in 4 days please anyone to send me the latest dumps will be highly appreciated
    spiderlan03 @ yahoo.com

  60. Anonymous
    October 24th, 2016

    Please someone could send me updates.
    300-101 route.
    Despite having studied very still I have difficulties with the English language and that of the dump help because some questions are difficult to understand.
    dowdp31 @ hotmail.com

    I appreciate the attention!

  61. ABCDE
    October 25th, 2016

    Hello everyone,

    I am going to appear for routing exam within 24-48 hours. It is very important for me to crack the exam. Please share the your experience and inform me regarding lab questions. Do you have the same lab as per digitaltut in exam ?? Please inform me about the lab.

    I got some questions from my Inner sources to crack the exam which i m going to post you below:

    Question. 1
    In which two ways can split horizon issues be overcome in a Frame Relay network environment? (choose two.)
    A. Configuring one physical serial interface with Frame Relay to various remote sites.
    B. Configure a loopback interface with Frame Relay to various remote sites.
    C. Configuring multiple subinterfaces on a single physical interface to various remote sites.
    D. Enabling split horizon.
    E. Disabling split horizon

    Question.2
    Which Easy Virtual Networking configuration component signific antly decreases network configuration?
    A. Easy Trunk
    B. Virtual Network Trunk
    C. VNET tags
    D. Dot1e
    E. MBGP

    Question. 3
    A network engineer receives reports about poor voice qualify issues at a remote site. The network engneer does a packet capture and sees out-of-order packets being delivered. Which optioncan cause the VoIP quality to suffer?
    A. Traffic over backup redundant links
    B. Load balancing over redundant links
    C. Speed duplex link issues
    D. Misconfigured voice VLAN

    Question. 4
    Other than a working EIGRP configration, which option must be the same on all routers for ELGRP

    authentication key role over to work correctly?
    A. SMTP
    B. SNMP
    C. Passwords
    D. Time

    Question. 5
    Refer to the following configuration command.
    Router(config)# ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
    Which statement about the command is true ?
    A. Any packet that is received in the inside interface with a source IP port address of 172.16.10.8:80 is translated to 172.16.10.8:8080.
    B. Any packet that is received in the inside interface with a source IP port address of 172.16.10.8:8080 is transtated to 172.16.10.8:80.
    C. The router accepts only a TCP connection from port 8080 and port 80 on IP address 172.16.10.8.
    D. Any packet that is received in the inside interface with a source IP address of 172.16.10.8 is redirected to port 8080 or port 80.

    Question. 6

    Refer to the exhibit. A network engineer has configured GRE between two IOS routers. The state of the tunnel interface is continuously oscilating between up and down. What is the solution to this problem?
    A. Create a more specific static poute to define how to reach the remote router.
    B. Create a more specific ARP entry to define how to reach the remote router.
    C. Save the configuration and reload the router.
    D. Check whether the internet service provider link is stable.

    Question. 7
    Which type of Ipv6 address is an identifier for a single interface on a single node?
    A. Anycast
    B. Broadcast
    C. Multicast
    D. Unicast

    Question.8
    Which two attributes describe UDP within a TCP/IP network? (Choose two.)
    A. Acknowledgments
    B. Unreliable delivery
    C. Connectionless communication
    D. Connection-oriented communication
    E. Increased headers

    Question. 9
    What command can you enter to configure an enable password that uses an encrypted password from another configuration?
    A. Enable secret 7 $abc%!#.Cd34$!ao0
    B. Enable secret 15 $abc%!#.Cd34$!ao0
    C. Enable secret 0 $abc%!#.Cd34$!ao0
    D. Enable secret $abc%!#.Cd34$!ao0
    E. Enable secret 6 $sab%!#.Cd34$!ao0
    F. Enable secret 5 $abc%!#.Cd34$!ao0

    Question.10
    Which three IP SLA performance metrics can you use to monitor enterpnse-class networks? (Choose
    three.)
    A. Packet loss
    B. Delay
    C. Connectivity
    D. Bandwidth
    E. Traps
    F. Reliability

    Question.12

    Refer to the exhibit showing complete command output. What type of OSPF router is router A?
    A. ABR
    B. Internal router
    C. ASBR
    D. Edge router

    Question. 13
    What is the optimal location from which to execute a debug command that produces an excessive amount of information?
    A. Vty lines
    B. SNMP commands
    C. A console port
    D. An AUX port

    Question. 14
    Which two statements about NTP operation are true? (Choose two.)
    A. If multiple NTP servers are configured, the one with the lowest stratum is preferred
    B. By default, NTP communications use UDP port 123.
    C. If mulitiple NTP servers are configured, the one with the highest stratum is perferred.
    D. Locally configured time overrides time received from an NTP server.
    E. “Stratum” refers to the number of hops between the NTP client and the NTP server.

    Question. 15
    A network engineer wants to display the statistics of an active tunnel on a DMVPN network. Which command should the administrator excute to accomplish this task?
    A. Router#show crypto ipsec sa
    B. Router#show crypto isakmp peers
    C. Router#show crypto isakmp sa
    D. Router#show crypto ipsec transform-set
    E. Router#show crypto engine connections active

    Question. 16
    In which from does PAP authentication send the user name and password across the link?
    A. Encrypted
    B. Password protected
    C. Clear text
    D. Hashed

    Question. 17

    Reter to the exhibit. Router 1 cannot ping router 2 via the Frame Relay between them. Which two statements describe the problems? (Choses two.)
    A. Encapsulation is mismatched.
    B. Frame Relay map is configured.
    C. DLCI is active.
    D. DLCL is inactive or deleted.
    E. An access list is needed to allow ping.

    Question. 18

    Refer to the exhibit. A network engineer is troubleshooting a DMVPN setup between the hub and the spoke. The enginner excuters thecommand show crypto isakmp sa and observes the output that is displayed. What is the problem?
    A. That ISAKMP is not enabled
    B. That ISAKMP is using default settings
    C. An incompatible IP sec transform set
    D. An incompatible ISAKMP policy

    Question. 19
    When a tunnel interface is configured in the default mode, which statement about routers and the tunnel destination address is ture?
    A. The router must have a route installed toward the tunnel destination.
    B. The router must have WCCP redirects enabled inbound from the tunnel destination.
    C. The router must have redirects enabled outbound toward the tunnel destination.
    D. The router must have Cisco Discovery Protocol enabled on the tunnel to form a CDP neighborship with the tunnel destination.

    Question.20
    A network engineer is configuring the router for NetFlow data exporting. What is requred in order for NDE to begin exporting data?
    A. Source
    B. Flow mask
    C. Destination
    D. Interface type
    E. Traffic type
    F. NetFlow version

    Question. 21
    At which layer does Cisco Express Forwarding use adjacency tables to populate addressing information?
    A. Layer4
    B. Layer 2
    C. Layer 1
    D. Layer 3

    Question. 22
    Which two functionalities are specific to stateless NAT64? (Choose two.)
    A. No requirement exists for the characteristics of Ipv6 address assignment.
    B. It does not conserve Ipv4 addresses.
    C. It provides 1-to-1 translation.
    D. It uses address overloading.
    E. State or bindings are created on the translation.

    Question. 23
    A network engineer wants to ensure an optimal end-to-end delay bandwidth product. The delay is less than 64 KB. Which TCP feature ensures steady state throughput?
    A. Window scaling
    B. Network buffers
    C. Round-trip timers
    D. TCP acknowledgments

    Question. 24
    Which IP SLA operation can be used to measure round-trip delay for the full path and hop-by-hop round-trip delay on the network?
    A. HTTP
    B. ICMP path echo
    C. TCP connect
    D. ICMP echo

    Question. 25
    What is the administrative distance for EBGP?
    A. 200
    B. 30
    C. 70
    D. 20

    Question. 26
    Considering the Ipv6 address independence requirement, which process do you avoid when yu use NPTv6 for transtation?
    A. Rewriting of higher layer information
    B. Ipsec AH header modification
    C. Checksum verification
    D. Ipv6 duplication and conservation

    Question. 27
    An engineer is using a network sniffer to troubleshoot DHCPv6 between a router and hosts on the LAN with the following configuration.
    Interface Ethernet0
    Ipv6 dhcp server DHCPSERVERPOOL rapid-commit
    !
    Which two DHCPv6 messages will appear in the sniffer logs? (Choose two.)
    A. Acknowledge
    B. Reply
    C. Advertise
    D. Accept
    E. Request
    F. Solicit

    Question. 28
    What is the function of the snmp-server manger command?
    A. To disable SNMP messages from getting to the SNMP engine
    B. To enable the device to send SNMP trps to the SNMP server
    C. To enable the device to send and receive SNMP reuests and responses
    D. To configure the SNMP server to store log data

    Question.29
    A network administrator notices that the BGP state drops and logs are generated for missing BGP thello keepalives. What is the potential problem?
    A. Incorrect neighbor options
    B. Hello timer mismatch
    C. BGP path MTU enabled
    D. MTU mismatch

    Question. 30
    A network administrator creates a static route that points directly to a multiaccess interface, instead of the next-jop IP address. The administrator notices that Cisco Express Forwarding ARPrequests are being sent to all destinations. Which issue might this configuration create?
    A. Low bandwidth usage
    B. High memory usage
    C. Cisco Express Forwarding routing loop
    D. High bandwidth usage
    E. IP route interference

    Question. 31

    Refer to the exhibit. Which three NTP features can be deduced on the router? (Choose three.)
    A. Only is in stratum 4
    B. Only accepts time requests from 192.168.1.1
    C. Only accepts time requests from 192.168.1.4
    D. Only handles four requests at a time
    E. Only updates its time from 192.168.1.4
    F. Only updates its time from 192.168.1.1

    Question. 32
    A network engineer wants to notify a manager in the event that the IP SLA connection los threshould is reached. Which two features are needed to implement this functionality? (Choose two.)
    A. SNMP traps
    B. MOS
    C. Cisco IOS EEM
    D. Logging local
    E. Threshould action

    Someone who appeared for exam this month pls reply me that do you have these questions in exam or not ? Any one who know the answers of this questions pls help me. It might help you to clear your own exam. This questions are latest exam questions as per my knowledge pls send me answers if you know.

    I have a exam within 24-48 hours so pls pls pls help me.

    Thanks for help. Thanks a lot.

  62. Mike
    October 25th, 2016

    I take the exam at the beginning of the month and I lost. I remember the horrible questions clearly and coincide with those published with ABCDE.

    No answers; it is clear missed the exam. But you already have an advantage.

    These are new questions + 149q and some of their simulations
    Only need to the new Drag and Drop.

  63. Ben
    October 25th, 2016

    ABCDE, right on the money, man!

  64. CC
    October 25th, 2016
  65. Ben
    October 25th, 2016

    Great work CC.

  66. NK2
    October 25th, 2016

    Any one cleared 300-101 ???

  67. HANI
    October 26th, 2016

    THANK YOU VERY MUCH CC.
    WE WANT CONFIRMATIONS FROM TEST TAKERS.
    DID THEY USE THIS AND CLEARED THE EXAM.

  68. Ben
    October 26th, 2016

    Gonna build a vce file with CCs link. will post shortly.

  69. Ben
    October 26th, 2016

    CC formatted. shttp://64.137.250.151:8080/tuts/CC.vce

  70. Ben
    October 26th, 2016

    ^remove the “s” in front of the http

  71. SF
    October 26th, 2016

    @ben
    please guide me what material to study for the hope that i might clear the exam

  72. Ben
    October 26th, 2016

    SF, In addition to the 183, ABCDE and CC posted more qs. I just moved the extra qs into a vce file. To use vce file, you’ll need a vce sim player. Can someone post that?

  73. raa
    October 27th, 2016

    please anyone have latest dump for 300-101 ?
    please send me raaedgerges @gmail.com

  74. marky
    October 27th, 2016

    can someone confirm the 149q plus the questions provided by CC is the valid exam ?

  75. Anonymous
    October 27th, 2016

    Hi guys! Thanks a lot ABCDE, CC and Ben.
    I read this topic carefully and understood that for preparing to exam 300-101 I need to use the dump 149q (because thera are some questions on the exam from this) and CC.vce with new questions.
    Am i need to use 183q dump? Is there any questions jn the exam from this dump?

  76. RAR
    October 27th, 2016

    WHAT ARE THE REAL QUESTIONS HAVE THE TEST NEXT WEEK, SOMEONE RECENTLY FILED

  77. BlackBelt
    October 27th, 2016

    I passed today. 8xx. 149q + 48q(“own dump created here”) are valid. Lab is the same. Att on network calcs for OSPF lab. Focus on OSPF. Follow it and u’ll be good to go. Labs OSPF, virtal link, pbr. Tks for all efforts here. U guys are a great team.

  78. Ben
    October 27th, 2016

    I’m headed in shortly also. Wish me luck@!

  79. Ben
    October 27th, 2016

    183 has many more drag and drops, I’d use that, the CC.vce and the additional 43q. you should be good. Everything unfamiliar from “a dear friends” last attempt are sprinkled in all 3 files.

  80. Anonymous
    October 28th, 2016

    Ben, how are you open vce files?

  81. HANI
    October 28th, 2016

    BEN,
    DID YOU TAKE THE EXAM?
    ANY FURTHER UPDATES FROM TEST TAKERS?

  82. Ben
    October 28th, 2016

    Hani,
    You’ll need VCE Exam Simulator. Can anyone post for Hani?

  83. dont_me
    October 29th, 2016

    I took the exam yesterday.. 724 score. 149q 150q and 180q not valid. same labs but multiple choice i don’t know where they get it from it’s like out of nowhere haha. prepared for 6 months but still no used. hahaha the only benefit i got is learning OSPF more and vrf, bgp haha

  84. Ben
    October 29th, 2016

    additional qs have been posted. see the last 2 pages of posts…

  85. HANI
    October 29th, 2016

    THANKS Ben,
    I have the vce file with the 48q. Also I have the 149q and 183q dumps.
    I just need some confirmations from you Ben and other test takers that the 48q vce file (from ABCDE & CC) is enough to pass the exam.
    So,when your exam starts Ben?, we appreciate any updates from you.

  86. HANI
    October 29th, 2016

    @dont_me
    CHECK THIS FILE
    https://drive.google.com/drive/folders/0B0GAuEbRMCwOa1BnZ3Q3WVBOcTg
    IS THE EXAM FROM IT?… DO YOU RECOGNIZE THE QUESTIONS?

  87. Ben
    October 29th, 2016

    Hani,
    Testing Next week. Had some scheduling conflicts this week.
    Got to get in there before the pool gets updated (again).

  88. Ben
    October 29th, 2016

    Hani, those are confirmed. Study them.

  89. Anonymous
    October 30th, 2016

    Hi, guys! VCE player here:
    ht tps: //yadi.sk/d/-ZY_rEXUxqCFX

  90. marky
    October 31st, 2016

    Ben, can you provide the link for the 183q vce ?

  91. HANI
    October 31st, 2016
  92. KD
    October 31st, 2016

    can anyone send me the 149q dumps please.
    frnc07atgmaildotcom

  93. HANI
    October 31st, 2016

    @KD
    this is the 149q vce file
    https://drive.google.com/open?id=0BxzHMmQ-WjBNTXFkUGpQNjVzcXc
    and
    this is the pdf file
    https://drive.google.com/open?id=0BxzHMmQ-WjBNZHhFM1pNYmZVenc
    YOU WILL NOTICE THAT THE 149Q DUMP IS PART OF THE 183Q DUMP.

  94. Ben2.0
    October 31st, 2016

    Passed with over 900 score.
    183 and revised CC.vce covers all.
    Labs: pbr, redist, virt links, stub.

  95. Mourad
    November 1st, 2016

    Ben 2. 0 which dump did you use please

  96. A n o n
    November 1st, 2016

    See his last post.

  97. slides
    November 1st, 2016

    i fail the exam the past oct 27th, the cc.vce is correct, Labs redist, virtual link, ospf multiple questions, chap drag&drop. thank hani do you help me whit swtich and arch exams?

  98. HANI
    November 1st, 2016

    @slides
    I haven’t studied for the switching exam, but what I know is that the 191q dump is still valid.
    I don’t know about the arch exams (is it the DESIGN)?
    ANY WAY ,CHECK THIS LINK: (THE CISCO FILE)
    https://www.mediafire.com/folder/9bmteb9f67uet/VCE_Files#76cacuurrta0d

  99. 12345
    November 1st, 2016

    Question. 1
    In which two ways can split horizon issues be overcome in a Frame Relay network environment? (choose two.)
    A. Configuring one physical serial interface with Frame Relay to various remote sites.
    B. Configure a loopback interface with Frame Relay to various remote sites.
    C. Configuring multiple subinterfaces on a single physical interface to various remote sites.
    D. Enabling split horizon.
    E. Disabling split horizon
    Question.2
    Which Easy Virtual Networking configuration component signific antly decreases network configuration?
    A. Easy Trunk
    B. Virtual Network Trunk
    C. VNET tags
    D. Dot1e
    E. MBGP
    Question. 3
    A network engineer receives reports about poor voice qualify issues at a remote site. The network engneer does a packet capture and sees out-of-order packets being delivered. Which optioncan cause the VoIP quality to suffer?
    A. Traffic over backup redundant links
    B. Load balancing over redundant links
    C. Speed duplex link issues
    D. Misconfigured voice VLAN
    Question. 4
    Other than a working EIGRP configration, which option must be the same on all routers for ELGRP
    authentication key role over to work correctly?
    A. SMTP
    B. SNMP
    C. Passwords
    D. Time
    Question. 5
    Refer to the following configuration command.
    Router(config)# ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
    Which statement about the command is true ?
    A. Any packet that is received in the inside interface with a source IP port address of 172.16.10.8:80 is translated to 172.16.10.8:8080.
    B. Any packet that is received in the inside interface with a source IP port address of 172.16.10.8:8080 is transtated to 172.16.10.8:80.
    C. The router accepts only a TCP connection from port 8080 and port 80 on IP address 172.16.10.8.
    D. Any packet that is received in the inside interface with a source IP address of 172.16.10.8 is redirected to port 8080 or port 80.
    Question. 6
    Refer to the exhibit. A network engineer has configured GRE between two IOS routers. The state of the tunnel interface is continuously oscilating between up and down. What is the solution to this problem?
    A. Create a more specific static poute to define how to reach the remote router.
    B. Create a more specific ARP entry to define how to reach the remote router.
    C. Save the configuration and reload the router.
    D. Check whether the internet service provider link is stable.
    Question. 7
    Which type of Ipv6 address is an identifier for a single interface on a single node?
    A. Anycast
    B. Broadcast
    C. Multicast
    D. Unicast
    Question.8
    Which two attributes describe UDP within a TCP/IP network? (Choose two.)
    A. Acknowledgments
    B. Unreliable delivery
    C. Connectionless communication
    D. Connection-oriented communication
    E. Increased headers
    Question. 9
    What command can you enter to configure an enable password that uses an encrypted password from another configuration?
    A. Enable secret 7 $abc%!#.Cd34$!ao0
    B. Enable secret 15 $abc%!#.Cd34$!ao0
    C. Enable secret 0 $abc%!#.Cd34$!ao0
    D. Enable secret $abc%!#.Cd34$!ao0
    E. Enable secret 6 $sab%!#.Cd34$!ao0
    F. Enable secret 5 $abc%!#.Cd34$!ao0
    Question.10
    Which three IP SLA performance metrics can you use to monitor enterpnse-class networks? (Choose
    three.)
    A. Packet loss
    B. Delay
    C. Connectivity
    D. Bandwidth
    E. Traps
    F. Reliability
    Question.12
    Refer to the exhibit showing complete command output. What type of OSPF router is router A?
    A. ABR
    B. Internal router
    C. ASBR
    D. Edge router
    Question. 13
    What is the optimal location from which to execute a debug command that produces an excessive amount of information?
    A. Vty lines
    B. SNMP commands
    C. A console port
    D. An AUX port
    Question. 14
    Which two statements about NTP operation are true? (Choose two.)
    A. If multiple NTP servers are configured, the one with the lowest stratum is preferred
    B. By default, NTP communications use UDP port 123.
    C. If mulitiple NTP servers are configured, the one with the highest stratum is perferred.
    D. Locally configured time overrides time received from an NTP server.
    E. “Stratum” refers to the number of hops between the NTP client and the NTP server.
    Question. 15
    A network engineer wants to display the statistics of an active tunnel on a DMVPN network. Which command should the administrator excute to accomplish this task?
    A. Router#show crypto ipsec sa
    B. Router#show crypto isakmp peers
    C. Router#show crypto isakmp sa
    D. Router#show crypto ipsec transform-set
    E. Router#show crypto engine connections active
    Question. 16
    In which from does PAP authentication send the user name and password across the link?
    A. Encrypted
    B. Password protected
    C. Clear text
    D. Hashed
    Question. 17
    Reter to the exhibit. Router 1 cannot ping router 2 via the Frame Relay between them. Which two statements describe the problems? (Choses two.)
    A. Encapsulation is mismatched.
    B. Frame Relay map is configured.
    C. DLCI is active.
    D. DLCL is inactive or deleted.
    E. An access list is needed to allow ping.
    Question. 18
    Refer to the exhibit. A network engineer is troubleshooting a DMVPN setup between the hub and the spoke. The enginner excuters thecommand show crypto isakmp sa and observes the output that is displayed. What is the problem?
    A. That ISAKMP is not enabled
    B. That ISAKMP is using default settings
    C. An incompatible IP sec transform set
    D. An incompatible ISAKMP policy
    Question. 19
    When a tunnel interface is configured in the default mode, which statement about routers and the tunnel destination address is ture?
    A. The router must have a route installed toward the tunnel destination.
    B. The router must have WCCP redirects enabled inbound from the tunnel destination.
    C. The router must have redirects enabled outbound toward the tunnel destination.
    D. The router must have Cisco Discovery Protocol enabled on the tunnel to form a CDP neighborship with the tunnel destination.
    Question.20
    A network engineer is configuring the router for NetFlow data exporting. What is requred in order for NDE to begin exporting data?
    A. Source
    B. Flow mask
    C. Destination
    D. Interface type
    E. Traffic type
    F. NetFlow version
    Question. 21
    At which layer does Cisco Express Forwarding use adjacency tables to populate addressing information?
    A. Layer4
    B. Layer 2
    C. Layer 1
    D. Layer 3
    Question. 22
    Which two functionalities are specific to stateless NAT64? (Choose two.)
    A. No requirement exists for the characteristics of Ipv6 address assignment.
    B. It does not conserve Ipv4 addresses.
    C. It provides 1-to-1 translation.
    D. It uses address overloading.
    E. State or bindings are created on the translation.
    Question. 23
    A network engineer wants to ensure an optimal end-to-end delay bandwidth product. The delay is less than 64 KB. Which TCP feature ensures steady state throughput?
    A. Window scaling
    B. Network buffers
    C. Round-trip timers
    D. TCP acknowledgments
    Question. 24
    Which IP SLA operation can be used to measure round-trip delay for the full path and hop-by-hop round-trip delay on the network?
    A. HTTP
    B. ICMP path echo
    C. TCP connect
    D. ICMP echo
    Question. 25
    What is the administrative distance for EBGP?
    A. 200
    B. 30
    C. 70
    D. 20
    Question. 26
    Considering the Ipv6 address independence requirement, which process do you avoid when yu use NPTv6 for transtation?
    A. Rewriting of higher layer information
    B. Ipsec AH header modification
    C. Checksum verification
    D. Ipv6 duplication and conservation
    Question. 27
    An engineer is using a network sniffer to troubleshoot DHCPv6 between a router and hosts on the LAN with the following configuration.
    Interface Ethernet0
    Ipv6 dhcp server DHCPSERVERPOOL rapid-commit
    !
    Which two DHCPv6 messages will appear in the sniffer logs? (Choose two.)
    A. Acknowledge
    B. Reply
    C. Advertise
    D. Accept
    E. Request
    F. Solicit
    Question. 28
    What is the function of the snmp-server manger command?
    A. To disable SNMP messages from getting to the SNMP engine
    B. To enable the device to send SNMP trps to the SNMP server
    C. To enable the device to send and receive SNMP reuests and responses
    D. To configure the SNMP server to store log data
    Question.29
    A network administrator notices that the BGP state drops and logs are generated for missing BGP thello keepalives. What is the potential problem?
    A. Incorrect neighbor options
    B. Hello timer mismatch
    C. BGP path MTU enabled
    D. MTU mismatch
    Question. 30
    A network administrator creates a static route that points directly to a multiaccess interface, instead of the next-jop IP address. The administrator notices that Cisco Express Forwarding ARPrequests are being sent to all destinations. Which issue might this configuration create?
    A. Low bandwidth usage
    B. High memory usage
    C. Cisco Express Forwarding routing loop
    D. High bandwidth usage
    E. IP route interference
    Question. 31
    Refer to the exhibit. Which three NTP features can be deduced on the router? (Choose three.)
    A. Only is in stratum 4
    B. Only accepts time requests from 192.168.1.1
    C. Only accepts time requests from 192.168.1.4
    D. Only handles four requests at a time
    E. Only updates its time from 192.168.1.4
    F. Only updates its time from 192.168.1.1
    Question. 32
    A network engineer wants to notify a manager in the event that the IP SLA connection los threshould is reached. Which two features are needed to implement this functionality? (Choose two.)
    A. SNMP traps
    B. MOS
    C. Cisco IOS EEM
    D. Logging local
    E. Threshould action

    @ABCDE

    I passed the exam today with a score 8XX. All of the questions that you mentioned are included in the exam (30 questions in total).

    For the detail of the exhibit, we can use below link from @cc:

    https://drive.google.com/drive/folders/0B0GAuEbRMCwOa1BnZ3Q3WVBOcTg

    There is a Drag and drop question about the CHAP process that cc also mentioned.

    Thank you so much!!!

  100. ciscoslim
    November 1st, 2016

    Past week I failed the test, Lab sims are similar, but the regular questions were indeed the questions shown on the posts above

Comment pages
1 2 3 4 7 205
  1. No trackbacks yet.